Polymer 80 build

The place for general discussion about guns, gun (and gun parts) technology discussion, gun reviews, and gun specific range reports; and shooting, training, techniques, reviews and reports.
User avatar
Candyman
Loose Cannon
Posts: 849
Joined: Wed Sep 10, 2008 2:29 am
Location: Denham Springs LA.

Polymer 80 build

Postby Candyman » Fri Mar 02, 2018 2:36 am

I decided to do a Polymer 80 GLOCK 19 build.
At first I was just going to build a frame and swap the upper from my Glock 19 Gen3 , but changed my mind.
I got the frame and frame kit from Brownell’s
5CA44740-8AE1-4778-8E58-C683CC600C2C.jpeg

I went with the Coyote tan with the abrasive grip.
24B50EEC-077B-4897-8574-A961B6F56ABC.jpeg

Today I ordered a Swenson barrel and slide, along with a slide kit to duild the slide. The only thing I need now is a set of sights.
You do not have the required permissions to view the files attached to this post.
Do not relish to feel what the men that used these weapons felt when they saw the elephant. For the elephant has tusk and to see him is to have his tusk dig deep into your soul. You will always have a part of you that will be cold and empty.

Rich Jordan
Trigger Junkie
Posts: 1635
Joined: Tue Aug 19, 2008 6:04 am

Re: Polymer 80 build

Postby Rich Jordan » Fri Mar 02, 2018 3:56 am

Watching with interest. I'm wishing I had bought one or two when they were on sale quite cheap last year. I think those were first gen models though and they had some issues.

User avatar
HTRN
Probably Unemployed
Posts: 10830
Joined: Wed Aug 20, 2008 4:05 am
Location: Under your bed with a knife
Contact:

Re: Polymer 80 build

Postby HTRN » Fri Mar 02, 2018 6:01 am

Theyre coming out with a subcompact frame in March, and supposedly a 10mm/45acp sized frame later this year. :ugeek:
HTRN, I would tell you that you are an evil fucker, but you probably get that a lot ~ Netpackrat

Describing what HTRN does as "antics" is like describing the wreck of the Titanic as "a minor boating incident" ~ First Shirt

Rich Jordan
Trigger Junkie
Posts: 1635
Joined: Tue Aug 19, 2008 6:04 am

Re: Polymer 80 build

Postby Rich Jordan » Sun Mar 04, 2018 7:14 am

HTRN wrote:Theyre coming out with a subcompact frame in March, and supposedly a 10mm/45acp sized frame later this year. :ugeek:


At last, real calibers.

User avatar
HTRN
Probably Unemployed
Posts: 10830
Joined: Wed Aug 20, 2008 4:05 am
Location: Under your bed with a knife
Contact:

Re: Polymer 80 build

Postby HTRN » Mon Mar 05, 2018 4:54 am

I keep thinking a polymer80 kit, along with a PA10 parts kit, along with some magpuls and a case of 175 grn fed gold medal inside a 4 inch pvc tube might make for a good idea...
HTRN, I would tell you that you are an evil fucker, but you probably get that a lot ~ Netpackrat

Describing what HTRN does as "antics" is like describing the wreck of the Titanic as "a minor boating incident" ~ First Shirt

User avatar
NVGdude
Trigger Junkie
Posts: 1705
Joined: Tue Aug 19, 2008 3:39 am
Location: Arizona

Re: Polymer 80 build

Postby NVGdude » Sat Mar 10, 2018 5:10 am

HTRN wrote:I keep thinking a polymer80 kit, along with a PA10 parts kit, along with some magpuls and a case of 175 grn fed gold medal inside a 4 inch pvc tube might make for a good idea...


We are thinking along similar lines.

User avatar
Candyman
Loose Cannon
Posts: 849
Joined: Wed Sep 10, 2008 2:29 am
Location: Denham Springs LA.

Re: Polymer 80 build

Postby Candyman » Wed Mar 14, 2018 8:04 pm

Well, I do have a habit of over doing things.
My plan was just to build the lower with the parts from the 19 Gen 3, but I ordered a lower parts kit with the frame. I ordered a Swenson slide and barrel from MidwayUSA along with a slide parts kit. So I built the gun with all new parts.
D12AAC6E-72F5-4E5F-A94E-F70892272B9E.jpeg

578C4AB6-D29D-4E03-8BA2-208A3A500212.jpeg


The first step was to remove the extra pieces from the top rail. I don’t have my drill press set up so I did it by hand.
I started with a sanding drum on my dremel.
D12236C9-A9AE-4106-8B7D-A2E5917EA84C.jpeg


I then switched to a high speed cutter bit.
BF68C479-E8D0-4537-906E-DA113D93E549.jpeg

FFBAA02F-CE32-461D-A94E-F1AAD03E0D8F.jpeg

F7F68ED9-79B2-4E65-9A05-4BE482DB7E0B.jpeg


The next step was to mill out the barrel block.
095F789B-C989-4354-B923-D9AF5A638169.jpeg

8264AC5E-A98B-42BD-9CA0-2FEF0A3EB89E.jpeg

A9CEF6B5-77AC-4B73-B77E-DF0995E489FF.jpeg


then drill the pin holes.
006CC26A-1FFA-4EA6-A5AC-9FAB66EF602A.jpeg

194BF9A5-EA49-463D-A11F-16276091AC2B.jpeg


Next was to put it all together.
9FE046A0-0EF4-4449-B08F-DA6B24062285.jpeg
You do not have the required permissions to view the files attached to this post.
Do not relish to feel what the men that used these weapons felt when they saw the elephant. For the elephant has tusk and to see him is to have his tusk dig deep into your soul. You will always have a part of you that will be cold and empty.

Rich Jordan
Trigger Junkie
Posts: 1635
Joined: Tue Aug 19, 2008 6:04 am

Re: Polymer 80 build

Postby Rich Jordan » Sat Mar 17, 2018 4:30 pm

Looking forward to the range report. I doubt these will go on sale anything like last year but I'm keeping eyes open just in case.

I'm hoping one of these will also work with a Mech Tech CCU to get a Glock-magazine fed carbine on the relatively cheap.

User avatar
Candyman
Loose Cannon
Posts: 849
Joined: Wed Sep 10, 2008 2:29 am
Location: Denham Springs LA.

Re: Polymer 80 build

Postby Candyman » Wed Mar 21, 2018 4:38 am

I went to the range last week. The red 6 and blue 3 were shot at 25 yards the rest were shot at 10 yards.
The gun really feels good in the hand. I like the flat trigger but need to shoot it more to get used to it.
0E88A1B9-9E03-4C53-B9FE-D9E8660ABDDA.jpeg
You do not have the required permissions to view the files attached to this post.
Do not relish to feel what the men that used these weapons felt when they saw the elephant. For the elephant has tusk and to see him is to have his tusk dig deep into your soul. You will always have a part of you that will be cold and empty.

Rich Jordan
Trigger Junkie
Posts: 1635
Joined: Tue Aug 19, 2008 6:04 am

Re: Polymer 80 build

Postby Rich Jordan » Thu Mar 22, 2018 3:38 am

Thanks. I'm regretting all the more not buying one or two of the kits last year when a site was clearancing them.


Return to “Guns and Shooting”

Who is online

Users browsing this forum: No registered users and 12 guests