Ye Olde Rifle Picture Thread
Posted: Thu Sep 24, 2015 11:43 pm
Most other gun forums have this, but for some reason we never started one. I'm not sure how we've survived 7 years without one, either, but that ends today. I would appreciate it if one of the moderators would see fit to make it a sticky. If somebody else wants to make handgun and shotgun threads, that would also be way cool. If you have pictures of your rifles that you are willing to share, please consider posting them here.
I will kick it off with the AR hater's AR:
That's a 10" Aero Precision upper in 300 AAC Blackout, on a registered SBR lower from PSA. Can is an AAC SDN-6, sitting on a Blackout 51T flash hider. Hogue furniture, BCM BCG, and Bobro low profile BUIS. Scope is a Nikon M-300 BLK, but I obviously I still need to order a mount. Hoping to test fire it with the irons over the next couple days.
Edit to add: I may have to hold off on the test firing. I'd previously bought one of those fancy Giessele alignment checking rods, mostly for the AKs because you can't look down the bore to check. Ran it down the AR bore with the can installed, and while it didn't hit anything, I am not happy with the alignment AT ALL, which is nowhere near to being centered (unlike the two rifles I had done by the smith, which are near perfect). I could easily see having a baffle or end cap strike, so I guess I should contact Aero and see what they have to say.
Edit II: Yeah, no longer convinced that the Aero barrel is necessarily going to be the problem...
Since I had the alignment rod out, I double checked the CZ with the can and the alignment rod (didn't do it last night), and found it was off too, where it was centered with the previous mount. Panicked, thinking I may have somehow effed up my can, I stuck it on the Saiga .308, on which it was always tight and centered, and it was still good there.
Took the new 1/2-28 mount off the CZ, cleaned all the Rocksett off the threads and installed it again to check installation... still off. Reinstalled the original 1/2-28 mount I put on there last spring (and removed last night due to looseness), and it was still loose, but centered. Switched to the second new mount, can is tight and centered on the CZ. I'll definitely be sending the first new mount back to Midway. But the upshot is, there's potentially that much error in the individual mounts, so it could be either the AR barrel, or the 5/8-24 mount (which is the one that came with my can).
Edit III: Tried another mount on the AR, and it's definitely the barrel. Sent the upper back to Aero for diagnosis and repair.
I will kick it off with the AR hater's AR:
That's a 10" Aero Precision upper in 300 AAC Blackout, on a registered SBR lower from PSA. Can is an AAC SDN-6, sitting on a Blackout 51T flash hider. Hogue furniture, BCM BCG, and Bobro low profile BUIS. Scope is a Nikon M-300 BLK, but I obviously I still need to order a mount. Hoping to test fire it with the irons over the next couple days.
Edit to add: I may have to hold off on the test firing. I'd previously bought one of those fancy Giessele alignment checking rods, mostly for the AKs because you can't look down the bore to check. Ran it down the AR bore with the can installed, and while it didn't hit anything, I am not happy with the alignment AT ALL, which is nowhere near to being centered (unlike the two rifles I had done by the smith, which are near perfect). I could easily see having a baffle or end cap strike, so I guess I should contact Aero and see what they have to say.
Edit II: Yeah, no longer convinced that the Aero barrel is necessarily going to be the problem...
Since I had the alignment rod out, I double checked the CZ with the can and the alignment rod (didn't do it last night), and found it was off too, where it was centered with the previous mount. Panicked, thinking I may have somehow effed up my can, I stuck it on the Saiga .308, on which it was always tight and centered, and it was still good there.
Took the new 1/2-28 mount off the CZ, cleaned all the Rocksett off the threads and installed it again to check installation... still off. Reinstalled the original 1/2-28 mount I put on there last spring (and removed last night due to looseness), and it was still loose, but centered. Switched to the second new mount, can is tight and centered on the CZ. I'll definitely be sending the first new mount back to Midway. But the upshot is, there's potentially that much error in the individual mounts, so it could be either the AR barrel, or the 5/8-24 mount (which is the one that came with my can).
Edit III: Tried another mount on the AR, and it's definitely the barrel. Sent the upper back to Aero for diagnosis and repair.